THE   BUMPER   GUY'S   GUN  SITE

THANKS FOR YOUR INTEREST IN MY BOLT STOP BUMPER!

At first inspection you might notice that my idea for a BOLT BUMPER - BOLT STOP - BOLT BUFFER  is made with hand tools. I make each one individually and personally in my shop. It does not look real high tech because - well - it isn't. But then again it did not cost you $15.00 to $20.00 plus $4.95 S&H. The after-market expensive commercial "buffers" may look more professional but, for instance, they may not work in all AK types and variants, as I personally experienced. My BOLT STOP BUMPER should fit your gun, will be easier to install, and will not interfere with your gun's cycling. My BOLT STOP BUMPER, plain and simple as it is, does work! Once installed you should notice immediately the difference in felt recoil and reduction in noise since the BOLT STOP BUMPER stops the carrier from slamming into the back of the receiver!

This is a semi-permanent installation. It should stay in while shooting your gun, but can be removed whenever you choose. There should be no need to remove the BOLT STOP BUMPER from your AK for your regular routine maintenance. The Mini 14/30, SKS & 10/22 L.R. BOLT STOP BUMPER should easily slip out, if desired.

AK or SKS: It is easy to install! Remove the receiver cover. Use a cleaning solvent that evaporates like Gun Scrubber, carburetor cleaner, or brake parts cleaner. Wipe clean the back of the receiver where the carrier slams into it. Put the BOLT STOP BUMPER there, at the back of the receiver, to see if it fits properly. The BOLT STOP BUMPER can be trimmed, if needed, with a new, sharp, one-edged razor blade. Please be careful not to cut yourself and do not remove too much material from the BOLT STOP BUMPER! For your SKS, no glue is needed, if you choose. The recoil spring will hold your BOLT STOP BUMPER in place. On your AK, you should put on a liberal amount of Super Glue on the 2 surfaces, back & bottom, of the BOLT STOP BUMPER that will touch the receiver. Wait about 1 or 2 minutes for the glue to start drying before installing. If it dries, that is OK. Just apply more glue again before you install your BOLT STOP BUMPER. Hold it in place for a few minutes and it should stay there because of the glue. If you ever have to remove it, it should come off by prying behind it with a screw driver and/or pulling it off with a pliers. CAUTION: Avoid getting rubber dissolving cleaning solvents on the "rubber" BOLT STOP BUMPER.

RUGER 10/22 L.R.: After you remove the stock, simply remove the original round metal bolt stop. It should slide right out. Your new after-market "Replacement" BOLT STOP BUMPER should slip right in. A little lubricant will help. The stock will hold it in place. Glue if you want, but not necessary.

RUGER MIN114/30: My BOLT STOP BUMPER has a hole where the recoil spring fits into. You can glue it to the front of the magazine well if you have a problem keeping it in place, but in most cases, is not be necessary.

NOTE: The back of the AK & 10/22 L.R. bolt carriers have sharp edges and will cut into the soft rubber BOLT STOP BUMPER. This is OK. The carrier will seat itself, but will not cut all the way through and the elimination of the metal to metal contact and the noise and felt recoil will still be reduced!

I hope that I am passing on an "idea" more than just selling you a product. The idea that we don't have to depend on the "system of things". As you can see from my idea, the solution (BOLT STOP BUMPER) to a problem (felt recoil & bolt slap noise) is fairly simple. Now you may even want to make your own. If not I will be glad to make and send you more as you need them. When "systems" fail people will survive, IF they help one another. I hope that I have helped you!

Any feed back and/or ideas are appreciated.

Email me click HERE.

Postal mail

"BOLT STOP BUMPERS"
C/O Dennis Harnisch
P.O.B. # 51461
Jacksonville Beach, FL 32240-1461